Got a cheap new bed frame and headboard from china for ~$100. Not the best but it doesn’t let me stub my toe.
Made:
Had one of these bed frames a few years back. Fine for sleeping but I’ll just say they don’t hold up very well to adult activities.
Mattress goes on top, not on side silly
Hell yeah. As far as unsolicited advice goes: invest in a good mattress and pillows as you go. The frame is whatever, but what’s under you while you sleep, sit, and walk is very valuable.
My partner and I have a like 5” memory foam topper and it turned our bed from “comfort” to “impossible to leave”
Would recommend
Thats what I have on this but 4”. I love it.
Everything that goes between your feet and the ground. Socks, shoes, chairs, mattress.
And hookers. Don’t skimp!
I ain’t got money to spend on hookers, i wouldn’t know
Tires
That too. And brakes. Both very important when it comes to stopping several tons of metal.
I recommend putting a rug underneath so as not to scrape the floor. Also I broke at least two similar looking bedframes having sex in them, so either don’t or just put the mattress on the floor
Excuse me sir, this is dull men’s club. None of us are having bed-breaking sex.
You don’t need to try that hard with these guys.
I like the no-stub feature. TBH this frame looks like one I would haphazardly design, so either they’re as bad as me or I’m better than I thought!
Should be fine, just might need to retighten the bolts after a couple months once like anything else.
I’ll highly recommend “blue” loctite (removable) or similar. It adds enough friction to the threads to keep them from backing out by themselves, but even a small amount of force from a tool will break it free again.
No more squeaks for the neighbors to overhear.
The true old skool technique is actually a single silk thread through the fastener first. A single old tie from a thrift store will last a lifetime. Silk thread was used in all kinds of things in automotive and aviation before gaskets were really a thing. It is tough, thin, and just plastic enough to deform in very tight compressed spaces, but it must be real silk and not synthetic.
Interesting!
I’d heard of using silk thread as a gasket maker (I had to split cases on a motorcycle engine and some old geezer mentioned that they used to use silk, but to just use RTV now), but not as a thread locker. I suppose the same principal applies, I just never gave it thought!
Silk is still used in some old aviation applications when it was originally specified and is sometimes preferred in racing. The service life is just shorter than gasket maker. Longer service-life solutions were needed with more modern casting techniques over the last couple of decades. Older stuff out of Detroit had poor old sand casting techniques that caused larger stack tolerances and lead to shorter service life. Modern stuff is nearly investment cast. It uses very strong binders and interlocking connections that prevent shifting and floating issues caused by large quantities of heavy molten metal. Old cheaper sand castings are not strong enough to form such connections. In aviation, everything is serviced with preventative maintenance, so the service life is tightly regulated and far shorter than silk will degrade. Likewise with racecars that will be rebuilt periodically.
It is a cool hack to know you could grab a spider web in the wild and have thread locker or seal a surface in a pinch.
Nice frame but I would be too scared to go with that headboard choice. My feline roommates would definitely turn that into a scratching post!
Does look like a scratching post/board thing lol
Didn’t even think about that. I guess I’ll see what happens.
That is one THIIIIC mattress! Get some more pillows for sure. Like 4 minimum, ideally 6. Also, get a rug for the floor. Much nicer stepping out of bed onto a plush rug.
That looks great! $100 is a steal.
Get a real blanket
I sweat enough with that thin little thing.
The thinner the better
I sleep in a bed. It’s nice.
Looks sturdy. Bet it doesn’t squeak.
Now to install the bass shaker engine.
I just assembled a VERY similar looking one with different materials a couple weeks ago. Mine had a plywood and denim facade around the steel frame, and two dozen 2x4s to support the mattress. I think it was around $200 from a local furniture store. Im guessing they imported it. Lol
I just got a new bed, and the frame has squared cups at all of the junction points. All you do is drop the frame prices together into the cups and it’s done! No tools or anything needed. It’s nice heavy plastic too.
